Rotary Drilling Rig Maintenance & Common Fault Repair

YG Wheeled Rotary Drilling Rig

Daily maintenance of rotary drilling rig

Routine maintenance needs to wipe clean the surface of the rotary drilling rig’s case. And pay attention to the cleaning and lubrication of the rig’s base slide, vertical shaft and other housings. Check whether all exposed bolts, nuts, safety pins, etc. are connected intact. Add lubricating oil or grease according to the lubrication requirements. Check the oil level of the transmission, transfer case and hydraulic system oil tank. In addition, check the oil leakage everywhere and deal with it according to the specific situation. Eliminate other faults. Pay attention to maintenance during daily use of rotary drilling rig. YG Drill Equipment Maintenance Department 24-hour consultation hotline: +8613838565351

Rotary Piling Machine
Rotary Piling Machine

Free Quote

Common malfunctions of rotary drilling rig

Leakage of hydraulic system

In winter and summer, the seals of the rotary drilling rig are prone to thermal expansion and contraction, which may cause leakage. Especially install O-shaped and rubber ring and other seal positions.

Fuel system maintenance

Replace diesel fuel regularly. Because diesel fuel is prone to deposits after long-term use. As a result, the viscosity of diesel oil increases and the flow becomes slower. Therefore, it is prone to waxing, atomization and insufficient combustion. It is easy to cause the diesel engine startability, power and economy to decline. When maintaining other parts, you also need to thoroughly clean all filters; disassemble the fuel filter; drain the sewage in the oil-water separator; eliminate potential safety hazards that may cause accidents.

rotary drilling equipment manufacturer
Rotary Drilling Equipment Manufacturer

Free Quote

Cooling system needs maintenance

Check the thermostat and heat preservation device, dispose of the cold diesel engine, replace and add antifreeze. If you are looking for the top drilling machine manufacturer, our company is the best choice definitely. Or if you have any problems about drill equipment, just leave your message, our professional manager will reply you within 12 hours.

The brake system needs maintenance

When replacing the brake fluid, all the original brake fluid must be discharged first. Inject new brake fluid. Check whether the oil-water separator can drain all the sewage. Check the condition of the brake system. And check whether the brakes are weakened or run off, and whether the pedaling force of the brake pedal is normal. Whether the brake does not return to position, make adjustments if necessary.

YG-360° wheeled rotary drilling rig
YG-360° Wheeled Rotary Drilling Rig

Free Quote

Electrical equipment needs maintenance

Battery; starter and generator; preheating device. Inaddition, if you have any other questions about drill rig electrical equipment, just leave your message.

Chassis and other maintenance items

Check whether the chassis bolts and nuts are tightened. Check for loose or missing steering system bolts. Apply lubricating oil to the place that needs lubrication, check the leakage of the chassis pipeline and solve it in time. If the chassis paint peel off is severely, you should do a spray anticorrosion treatment inspection to keep the chassis working normally. If you are looking for high quality and cheap rotary drilling rig for sale, please feel free to contact us at any time. YG will be your ideal partner.

YG153 dth drilling rig details
YG153 DTH Drilling Rig Details

Free Quote

Related drill rigs

As a professional crawler drilling machine manufatcturer, YG Machinery has a series of drilling rigs with different functions and uses. For example, water well drilling machine, Down the hole drilling machine, HDD (Horizontal Directional Drilling) machine. Anchor drilling rig. Rotary drilling rig for sale. Backpack core drilling machine. And mountain drilling rig, etc. Please leave your requirement by fill the following form. Or you can chat with us directly by WhatsApp or Online Service.

Drilling Rig Accessories

We have a series of drilling rig accessories for sale to match the use of the drilling rig. For example, drilling pipedrill bitmud pumptriplex mud pumpindustrial air compressorscrew air compressor, etc.

    Please feel free to give your inquiry in the form below. We will reply in 24 hours.
    Product Model:
    Name(required):
    Email(required):
    Phone(required):
    Country:
    WhatsApp(required):
    Your Message(required):

    Types & Principles of Drilling Equipment For Sale

    Integrated DTH Drilling Equipment For Sale

    Percussion drilling equipment for sale

    The percussion rig relies on the vertical reciprocating movement of the drilling tool to make the drill bit hit the bottom of the well to break the rock formation. The percussion drilling rig has a simple structure without a circulating well-washing system. And the removal of cuttings and the drilling rig cannot be carried out at the same time, so the efficiency is low. The drilling depth is generally within 250 meters, sometimes up to 500-600 meters. There are mainly the following 2 types of drilling equipment for sale.

    Punch grab cone

    The punching cone uses the weight of the drilling tool itself to hit the formation. At the lower end of the drilling, the tool is several sharp-angled gripping flaps that can be opened and closed. When the drilling tool moves downward under the action of its own weight. The gripping flaps are opened and cut into the rock formation. Then the drilling tool is lifted by the hoist through the wire rope, and the cuttings are grabbed into the cone by the gripping flap during the closing process, and the cuttings are lifted out of the wellhead. The drilling depth is usually 40-50 meters, and the deepest is 100-150 meters.

    Wire rope impact drill machine for sale

    It is composed of a mast, a lifting pulley, a steel wire rope, an impact mechanism, a drilling tool, and a motor mounted on the top. During operation, the motor drives the impact mechanism through the transmission device and drives the steel wire rope to make the drill reciprocate up and down. When moving downwards, the weight of the drill bit itself cuts into and breaks the rock formation. And the upward movement is pulled by a wire rope. The stroke of the drill bit is 0.5 to 1 meter, and the impact frequency is 30 to 60 times per minute. The cuttings are cleared out of the ground by the sand pump, and drilling and cuttings are removed at the same time.

    Percussion types drilling rig for sale
    percussion types drilling rig for sale

    Free Quote

    Rotary drilling rig

    The rotary drilling rig relies on the rotary motion of the drilling tool to break the rock formation to form holes. As a leading drilling equipment supplier in China, there are mainly the following 5 types of drilling equipment for sale.

    Pot cone drilling equipment for sale

    Use a pot cone drill to rotate and cut the soil layer. The big pot cone and the small pot cone are called according to the size of the drilling tool, which can be driven by manpower or power. The cut soil debris falls into the pot and is lifted to the ground to be discharged. The pot cone has a simple structure and low efficiency. And is suitable for general soil or sand and gravel soil. The drilling depth of the small pot cone is 80-100 meters, and the large pot cone is 30-40 meters.

    Rotary drilling rig with circulating mud pump

    It is composed of a tower, hoist, turntable, drilling tool, mud pump, faucet, and electric motor. During operation, the power machine drives the turntable through the transmission device. The active drill rod drives the drill bit to rotate and break the rock formation. There are positive and negative circulation methods. When the positive circulation drilling rig is working. The bottom hole cuttings are carried out of the wellhead through the annular channel outside the drill pipe. After the sedimentation tank settles, the mudflows back to the mud tank for recycling. Contact us to get rotary drilling equipment for sale price.

    When the reverse circulation drilling rig is working, the mudflows into the bottom of the well from the wellhead after it settles in the sedimentation tank. And the mud that carries the cuttings is sucked out of the well through the drill pipe cavity by the sand pump through the bit nozzle and sinks back to the sedimentation tank. The drilling rig forms a high rising velocity in the drill pipe. And has a strong ability to discharge cuttings and pebbles. Circulating mud washing rotary drilling rig has a fast drilling speed and is suitable for loose formations where the diameter of the soil, sand. And pebbles is smaller than the inner diameter of the drill pipe. The drilling depth is generally within 150 meters.

    rotary types crawler drilling machine for sale
    rotary types crawler drilling machine for sale

    Free Quote

    Rotary drilling rig with compressed air flushing well

    On the rotary drilling rig, the air compressor is used to replace the mud pump, and the compressed air is used to replace the mud to wash the well. The reverse circulation method is usually used, also known as gas lift reverse circulation. It is suitable for arid areas with large-good depths and water shortage and permafrost in cold zones.

    Hydraulic power head drilling rig

    It is driven by a hydraulic motor through a reducer, and a powerhead that moves up and down along the tower replaces the turntable and faucet on the turntable drill to drive the drill rod and bit to rotate and cut the rock formation. Large diameter water wells can be drilled.

    YG Crawler Mounted Anchor Drilling Rig With Full Hydraulic Power Head
    YG Crawler Mounted Anchor Drilling Rig With Full Hydraulic Power Head

    Free Quote

    DTH vibration rotary drilling equipment for sale

    Drilling into the rock formation by a combination of vibration and rotary motion. The drilling tool is composed of a drill bit, a vibrator, a vibration absorber and a guide tube. The vibrating force generated by the vibrator makes the whole drilling tool make a cone pendulum movement to break the rock formation. The compressed air reverse circulation method is used to wash the well. So that the cuttings are discharged out of the well through the pipe and the inner cavity of the drill pipe. The drilling depth can reach 150 meters.

    DTH Drilling Machine For Sale
    DTH Drilling Machine For Sale

    Free Quote

    Compound drilling equipment for sale

    There are 2 types of compound drilling equipment for sale. One is a water well drilling rig that combines impact and rotation, such as a pneumatic down-the-hole hammer drill. The down-the-hole hammer drill is composed of a cylinder liner and a piston. The high-pressure air provided by the industrial air compressor drives the piston to reciprocate up and down, impacting the drill bit to enhance the drill bit’s ability to drill into the rock formation. At the same time, the drilling tool rotates at a relatively low speed of 35-60 rpm. The air discharged from the upper and lower cavities of the piston enters the drill bit and carries the bottom cuttings out of the wellhead. The pneumatic down-the-hole hammer drill can be used for drilling deep wells in hard rock formations, with high drilling speed and straight boreholes.

    The other is to add a percussion mechanism on the basis of the rotary drilling rig. Which is mainly used for rotary drilling. When encountering a pebble layer, the two-water well drilling rig that uses percussion drilling is highly adaptable to various formations. If you need to buy any type of drilling machine, please feel free to contact the YG drill equipment manufacturer.

    Free Quote

    Related products

    As a professional engineering drill machine supplier, the YG drill equipment factory has different drill equipment suitable for various construction purposes and environments. Such as DTH drilling machine, anchor drilling machine, rotary drilling machine, HDD horizontal directional drilling machine, backpack core drill rig, portable screw air compressor, mountain drill machine, and so on. Welcome drilling rigs dealer discuss cooperation with us. Our sales manager will reply to you within 12 hours.

    Drilling Rig Accessories

    We have a series of drilling rig accessories for sale to match the use of the drilling rig. For example, drilling pipedrill bitmud pumptriplex mud pumpindustrial air compressorscrew air compressor, etc.

      Please feel free to give your inquiry in the form below. We will reply in 24 hours.
      Product Model:
      Name(required):
      Email(required):
      Phone(required):
      Country:
      WhatsApp(required):
      Your Message(required):